Marantec Comfort 150 Betriebsanleitung

Comfort 220.2, 250.2, 252.2, 250.2 speedOperator system for Garage DoorsInstallation and Operating InstructionsGB

6. Installation6.5 Release• Construct a physical barrier to limit the extent of thedoor travel in the opening direction.• Check that the release pull

6. Installation6.6 Connection of control elements Attention!In order to avoid damaging the controls:- The local safety regulations must becomplied wit

6. InstallationTerminal XB01Advice:If a photocell is to be connected, itmust be installed before the expressprogramming procedure is carried out. The

Connect hand transmitter.7. Hand transmitter7.2 Hand transmitter coding 7.2.1 Transfer the coding • Actuate the master transmitter and hold the button

Plugging in the module antenna.8.1 / 1P1234567812ABDCOperating elementsLabel Type / functioniA Carousel display 8.3B OPEN button (+) (e.g. to drive

8. Initial operationLegend:LED offLED onLED flashes slowlyLED pulsesLED flashes quicklyFactory default settingNot possible –8.4 Express programmingThe

Operatingmode1.P1x >2s <10sStart express programming / Programme the doorOPEN end position2.Drive the door to the OPENposition3.Correct the OPE

8. Initial operationCaution!The automatic cut-out must be correctly programmed for the CLOSEand OPEN directions to prevent damageto persons or proper

9.1 Programming structure for extended operator functions (Example for Level 2, Menu 2)End programmingParameterMenuLevelsLevel 3Level 4Menu 3Menu 2Men

9. Extended operator functionsLevel Menu Factory default settingLevel 1 – Basic functionsMenu 3: Intermediate position OPEN –Menu 4: Intermediate pos

1. Meaning of symbols . . . . . . . . . . . . . . . . . . .22. Table of contents . . . . . . . . . . . . . . . . . . . . . .23. General safety advice

9. Extended operator functionsLevel Menu Factory default settingLevel 6 - Variable speedMenu 1: Speed OPEN Setting 16Menu 2: Soft run speed OPENSettin

9. Extended operator functions9.3 Functions overview for the levelsCaution!Important factory default settings can be changed using the extended funct

9. Extended operator functionsReference:If changes are made in Menus 3 and 4 in Level 1, a new performance check must be carried out(Section 8.5).iMen

9. Extended operator functions* The higher the setting, the higher the driving power.** The lower the setting, the more sensitive the automatic cut-o

9. Extended operator functionsAdvice:- The automatic closing timer can only be programmed if a photocell barrier is connected.- The functions in Menu

9. Extended operator functionsMenu 1: Automatic closing timerSettingDoor open durationWarning timeAutomatic closing timerOther functionsA1 - - deacti

9. Extended operator functionsLevel 4 – Remote programmingMenu 2: Intermediate positionLED 7 flashes slowly -> press the hand transmitter button -&

9. Extended operator functionsLevel 6 - Variable speed1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16Menu 1: Speed OPEN (in increments)– – – – – – 7 8 9 10 11

9. Extended operator functionsLevel 8 – System settings1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16Menu 1: PhotocellA1 B1 C1 D1 – – – – – – – – – – – –Menu

9. Extended operator functionsSetting Door movement, OPEN Door movement, CLOSEA3 Door stopsDoor reverses a little1B3Door reverses a little1Door revers

3. General safety advicePlease read carefully!Target groupThis operator system may only be installed, connected and put intooperation by qualified and

9. Extended operator functionsMenu 5: Function of the direction command transmitterMenu 6: Function of the impulse command transmitter Setting Direc

10.1 Malfunctions without error messagesError Cause SolutionLED 8 does not light up. - No voltage. - Check that the mains power supply is operational.

Error Cause SolutionMessage 7 - If no buttons are pressed within 120 seconds, the programming mode terminates automatically.- OPEN and CLOSED door pos

10. MessagesLegend:LED offLED onLED flashes slowlyLED pulsesLED flashes quicklyFactory default settingNot possible –Error Cause SolutionMessage 26 - U

11.1 Technical Data for Comfort 220.2, 250.2, 252.2, 250.2 speed11. AttachmentElectrical data Comfort 220.2 Comfort 250.2 Comfort 252.2 Comfort 250.2

11.2 Manufacturer’s Declaration11.3 EC Declaration of ConformityWe hereby declare that the product sold by us and mentioned below corresponds in its d

Valid from: 04.2009#83 9881 - GB 360283 - M - 0.5 - 0308English Copyright.No part of this manual may be reproduced without our prior consent.Subject t

4 Installation and Operating Instructions, Comfort 220.2, 250.2, 252.2, 250.2 speed GB (#83988)4.1 Comfort 220.2, 250.2, 252.2,250.2 speed supply pack

Installation and Operating Instructions, Comfort 220.2, 250.2, 252.2, 250.2 speed GB (#83988) 54. Product overview15 Mini hand transmitter16 Micro han

4. Product overview6 Installation and Operating Instructions, Comfort 220.2, 250.2, 252.2, 250.2 speed GB (#83988)Attention! In order to guarantee cor

Installation and Operating Instructions, Comfort 220.2, 250.2, 252.2, 250.2 speed GB (#83988) 7Install door link.Release sliding carriage.6.1 Installi

8 Installation and Operating Instructions, Comfort 220.2, 250.2, 252.2, 250.2 speed GB (#83988)Installation on the up-and-over door.10 - 50 mmInstalla

Installation and Operating Instructions, Comfort 220.2, 250.2, 252.2, 250.2 speed GB (#83988) 9Mount the suspension cramps at the mounting positions.1